Home > Search by Brand
Choose a sub category:
ARP DNJ Engine Fuel Injector Clinic
Gates Genuine Honda OEM Green Filter USA
Hasport Hawk Performance Insane Shafts
Sort By:
Page of 2
J32A1 & J32A2 Engine Timing Belt Idler Pulley DNJ J32A2 & J32A1 Engine Timing Belt J32A2 Head Gasket
J32A2 Head Gasket
Our Price: $27.99
01-03 Acura CL, TL .  Fits both base and Type S. High Quality OE Replacement Timing belt for J32A2 & J32A1 engines. OE Replacement Head Gasket for J32A2 Engine.
Head Gasket for J32A3 Engine J32A1 & J32A2 Engine Timing Belt Tensioner Pulley J Series AC Delete Belt
J Series AC Delete Belt
Our Price: $37.99
OE Replacement Head Gasket for J32A3 Engine. J32A1 & J32A2 Engine Timing Belt Tensioner Pulley This 6 rib belt is used to eliminate the AC compressor on most J series engines.  This belt runs direct from the Crank Pulley to the Alternator without the need to use any belt tensioner.  No AC or Power Steering.
Gates Racing J32A2/J32A1 Timing Belt P2R DNJ High Compression J Series 89.5mm Piston Set P2R DNJ High Compression J Series 89mm Piston Set
Gates Racing Blue Timing Belt

P2R is proud to offer DNJ High Compression Pistons for the Honda J series engines. These pistons are OE style cast replacement pistons, and includes pistons, rings, wrist pins, and clips. Friction coated Side skirts for reduced wear.

Bore: 89.5mm

Compression Ratio:

J32 crank & rods = 11.2:1

J35 crank & rods = 12.1:1

J37 crank & rods = 12.4:1

P2R is proud to offer DNJ High Compression Pistons for the Honda J series engines. These pistons are OE style cast replacement pistons, and includes pistons, rings, wrist pins, and clips. Friction coated Side skirts for reduced wear.

Bore: 89 mm

Compression Ratio:

J32 crank & rods = 11.1:1

J35 crank & rods = 12.0:1

J37 crank & rods = 12.3:1

ARP Head Studs for Honda V6 J Series Engines ARP Head Studs - 13+ Honda Accord V6 Insaneshafts K-series axles
Custom set of ARP Head Studs for Honda V6 J Series Engines Custom set of ARP Head Studs for 2013+ Honda Accord V6.

Honda/Acura application with any K-series motor swap. 500whp rated axles. Engineered for all your high performance needs. Race proven on drag and circuit tracks. Similar to OEM specs but re-engineered to provide the end user with not only a better product but a stronger and more durable CV axle.InsaneShafts has developed an affordable high quality product for all your racing needs. Whether for drag racing, road racing or daily use, these axles have proven to last. InsaneShafts has a long history of developing custom CV axles for many off-road vehicles.

This swap axle requires no hub/spindle modifications (even swap axles). It has been designed to give the consumer the best product for the money and have stood toe to toe against all your bigger stage axles

Insaneshafts J-series axles Hasport EGJ2 J-Swap Mount Kit 365cc FIC Honda J-Series ('04+) Fuel Injector Clinic Injector Set (High-Z)

Honda/Acura application with a J-series motor swap. 500whp rated axles. Engineered for all your high performance needs. Race proven on drag and circuit tracks. Similar to OEM specs but re-engineered to provide the end user with not only a better product but a stronger and more durable CV axle.InsaneShafts has developed an affordable high quality product for all your racing needs. Whether for drag racing, road racing or daily use, these axles have proven to last. InsaneShafts has a long history of developing custom CV axles for many off-road vehicles.

This swap axle requires no hub/spindle modifications (even swap axles). It has been designed to give the consumer the best product for the money and have stood toe to toe against all your bigger stage axles

*The swap axle listing for 92-00 Civic/94-01 Integra are for the older style female halfshaft.
**If you are looking for a swap axle with a newer male halfshaft please contact us.

Performance mount kit for the J-Series V6 engines (with 04-08 TL or 03-07 Accord 6-speed transmission) into the 92-95 Civic / 94-01 Integra / 93-97 Del Sol.

Like all Hasport Mount Kits, it's designed using sophisticated CAD/CAM software. This kit features:

  • Dual mount height. The engine can be mounted low enough to clear the hood or 1.9 inches higher for additional ground clearance. (J32A2 engine and unmodified Civic hood)
  • Designed blending strength and style with a lifetime warranty for worry free use.
  • Four different bushing durometers for applications ranging from daily driver the 8 second drag car.
  • Hasport's superior customer service.


We recommend using one of the following engines:

  • J30A1 from 98-02 Accord or 97-99 Acura CL
  • J32A1 from 99-03 Acura TL or 01-03 Acura CL
  • J32A2 from 01-03 Acura CL Type S or 02-03 Acura TL Type S

NOTE: Mounts take about 7-10 Days before shipping.
Honda J-Series ('04+) Fuel Injector Clinic Injector Set: 6 x 365cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
365cc FIC Honda J Series ('98-'03) Fuel Injector Clinic Injector Set (High-Z) 445cc FIC Honda J-Series ('04+) Fuel Injector Clinic Injector Set (High-Z) 445cc FIC Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set (High-Z)
Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set: 6 x 365cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
Honda J Series ('04+) Fuel Injector Clinic Injector Set: 6 x 445cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set: 6 x 445cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
525cc FIC Honda J-Series ('04+) Fuel Injector Clinic Injector Set (High-Z) 525cc FIC Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set (High-Z) Hasport EKJ1 - J Series Mount Kit
Honda J-Series ('04+) Fuel Injector Clinic Injector Set: 6 x 525cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.

Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set: 6 x 525cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.

Performance mount kit for the J-Series V6 engines (with 04-08 TL or 03-07 Accord 6-speed transmission) into the 96-00 Civic.


This mount kit is designed to work with an EG/DC rear cross member, lower control arms and steering rack.


Like all Hasport Mount Kits, it's designed using sophisticated CAD/CAM software. This kit features:

  • Optimized engine placement for ground clearance (same as D or B-Series) and axle angle
  • Designed blending strength and style with a lifetime warranty for worry free use.
  • Four different bushing durometers for applications ranging from daily driver the 8 second drag car.
  • Hasport's superior customer service.


We recommend using one of the following engines:

  • J30A1 from 98-02 Accord or 97-99 Acura CL
  • J32A1 from 99-03 Acura TL or 01-03 Acura CL
  • J32A2 from 01-03 Acura CL Type S or 02-03 Acura TL Type S
Hasport EKJ2 - J Series Mount Kit 650cc FIC Honda J-Series ('04+) Fuel Injector Clinic Injector Set (High-Z) 650cc FIC Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set (High-Z)

Performance mount kit for the J-Series V6 engines (with 04-08 TL or 03-07 Accord 6-speed transmission) into the 96-00 Civic.


This mount kit is designed to work with an EG/DC rear cross member, lower control arms and steering rack.


Like all Hasport Mount Kits, it's designed using sophisticated CAD/CAM software. This kit features:

  • Dual mount height. The engine can be mounted low enough to clear the hood or 1.9 inches higher for additional ground clearance. (J32A2 engine and unmodified Civic hood)
  • Designed blending strength and style with a lifetime warranty for worry free use.
  • Four different bushing durometers for applications ranging from daily driver the 8 second drag car.
  • Hasport's superior customer service.


We recommend using one of the following engines:

  • J30A1 from 98-02 Accord or 97-99 Acura CL
  • J32A1 from 99-03 Acura TL or 01-03 Acura CL
  • J32A2 from 01-03 Acura CL Type S or 02-03 Acura TL Type S
Honda J-Series ('04+) Fuel Injector Clinic Injector Set: 6 x 650cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set: 6 x 650cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
775cc FIC Honda J-Series ('04+) Fuel Injector Clinic Injector Set (High-Z) 775cc FIC Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set (High-Z) 1000cc FIC Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set (High-Z)
Honda J-Series ('04+) Fuel Injector Clinic Injector Set: 6 x 775cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set: 6 x 775cc Saturated / High Impedance Ball & Seat Injectors. These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and tight manufacturing tolerances make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set: 6 x 1000cc Saturated / High Impedance Ball & Seat Injectors. Utilizing the latest injector technology and featuring state of the art matching with Data Match Technology . Includes pigtails PGT USC6 or add Plug & Play adaptors PADPUtoH6. Previously known as IS118-0900H.

This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
1100cc FIC Honda J-Series ('04+) Fuel Injector Clinic Injector Set (High-Z) 1100cc FIC Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set (High-Z) 2150cc FIC Honda J Series ('04+) Fuel Injector Clinic Injector Set (High-Z)
Honda J-Series ('04+) Fuel Injector Clinic Injector Set : 6x1100cc Saturated / High Impedance Ball & Seat Injectors. Utilizing the latest injector technology and featuring state of the art matching with Data Match Technology . Includes pigtails PGTJETR6Q or add Plug & Play adaptors PADPJtoH6

Fuel Injector Clinic’s 1100cc/min high impedance injector is the largest injector that has excellent idle performance in street driven cars while still providing enough fuel to support mid to high horsepower output. The Fuel Injector Clinic 1100cc injector is 20% larger than our 900cc (Fuel Injector Clinic 900cc is the same as ‘1000cc’ sold by others).

The 1100cc high impedance injector can be used with any fuel type. It is compatible with pump gasoline, E85, and all race fuels!

This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
Honda J-Series ('98-'03) Fuel Injector Clinic Injector Set : 6x1100cc Saturated / High Impedance Ball & Seat Injectors. Utilizing the latest injector technology and featuring state of the art matching with Data Match Technology . Includes pigtails PGTJETR6Q or add Plug & Play adaptors PADPJtoH6

Fuel Injector Clinic’s 1100cc/min high impedance injector is the largest injector that has excellent idle performance in street driven cars while still providing enough fuel to support mid to high horsepower output. The Fuel Injector Clinic 1100cc injector is 20% larger than our 900cc (Fuel Injector Clinic 900cc is the same as ‘1000cc’ sold by others).

The 1100cc high impedance injector can be used with any fuel type. It is compatible with pump gasoline, E85, and all race fuels!

This injector set is precisely matched using Fuel Injector Clinic's proprietary Data Match Technology. Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

Superior short pulse width control and state of the art matching make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. If you are using aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our lifetime warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.
Honda J-Series ('04+) Fuel Injector Clinic Injector Set : 6 x 2150cc Saturated / High Impedance Injectors. Utilizing the latest injector technology and featuring state of the art matching with Data Match Technology . Great injector for E85 or other high volume fuels! These injectors do not require a resistor pack or P&H drivers. Includes pigtails PGT DEN6 or add Plug & Play adaptors PADPDtoH6. DO NOT USE WITH VP Import, Q16 or OTHER MTBE OXYGENATED FUELS

This massive injector is in a class of its own when low end throttle response and short pulse width control is required. State of the art Data Match Technology dynamic flow matching is used during the production of these injector sets due their large flow rate. This significantly improves the ECU’s ability to control these injectors in the sub 2ms pulse width area, typical of idle and part throttle conditions.
Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

CAUTION! The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please be sure to follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.A